Robot36 - SSTV Image Decoder

Audio inputs

• Microphone: decode live SSTV audio.
• Files: import WAV (8/16/24/32-bit integer PCM or 32/64-bit IEEE float), FLAC, or MP3. Mono and stereo files at 8–192 kHz use their own sample rate and channel count, independently of microphone settings.
• Playback capture: decode audio playing in other apps on Android 10 or later, after granting system capture permission.

In File mode, tap + to choose a file, then Play. Normal playback includes audible monitoring; Turbo decodes without playback or real-time pacing. Its speed depends on the device and SSTV mode. Stopping and pressing Play again restarts the file. At the end, the decoder drains its buffered audio so complete images can be saved when automatic saving is enabled.

Limitations

• Prefer original WAV or FLAC recordings. MP3 is lossy and may introduce image noise, color errors, or decoding failures; a brief, non-blocking notice appears on each MP3 selection. Other compressed formats are not currently supported.
• MP3 and FLAC use Android's media components. On some devices, 24-bit FLAC is output as 16-bit PCM, so full source precision is not guaranteed.
• Playback capture depends on the source app allowing its audio to be captured; it cannot capture every app or stream.

Audio Line-Level to Microphone-Level Converter

Decoding SSTV signals is more reliable with a clean input. Using a direct cable connection instead of acoustic coupling avoids echo, distortion, and environmental noise.

Most smartphones use TRRS connectors for headsets. In these connectors, the sleeve and the second ring (next to the sleeve) serve dual roles: depending on the standard, one is the microphone input and the other is ground. The tip and first ring carry the left and right audio channels.

When a TRS plug is inserted into a TRRS jack, the sleeve and second ring are shorted together. This allows regular stereo headphones (without a microphone) to work correctly.

Instead of determining which pin is MIC or GND for each device, galvanic isolation can be used. This avoids compatibility issues, eliminates ground loops, protects against damage, and improves robustness.

Using a line-level output (e.g., from a radio or sound card) as a microphone input introduces several challenges:

• Line-level signals swing around 1 V, while electret microphones produce signals in the millivolt range, so attenuation is needed.
• Electret microphones are biased via the TRRS connector, allowing their internal amplifiers to function. This bias must be blocked to avoid distortion.
• To make the smartphone recognize the input as a microphone, a resistor must be placed between the second ring and sleeve.

To reduce power consumption on the line-out device, a higher impedance can be achieved by inserting a resistor in series with the primary winding of a 1:1 audio transformer. If the source cannot drive high impedance, the primary can be connected directly, and attenuation applied on the secondary side. This increases power consumption and may heat the transformer.

Because the electret mic input is high-impedance and AC-coupled, the transformer’s secondary can resonate if left unterminated. Adding a resistor across the secondary dampens this resonance and flattens the frequency response. A value equal to the transformer’s impedance is typical, but a lower value can be used to both improve damping and provide additional attenuation. The ratio of the series resistor on the primary to the parallel resistor on the secondary determines the overall attenuation.

Example Values

• Transformer: 1:1 audio transformer, 600 Ω impedance, 140 Ω DC resistance
• Primary side: 2.2 kΩ resistor in series (any value between 1 kΩ and 10 kΩ is fine; a 10 kΩ potentiometer allows adjustment)
• Secondary side: 100 Ω resistor across the winding for damping and attenuation
• DC blocking capacitor: 2.2 µF film capacitor (anything between 1 µF and 100 µF works; avoid values below 1 µF to keep low-frequency SSTV content intact)
• Microphone sensing resistor: 2.2 kΩ between the second ring and sleeve (values near 2 kΩ are fine)

Schematic

 [Line IN] O---[R1]---+||+---+---|C1|---+---O [Ring 2]
                      S||S   |          |
                  T1: S||S  [R2]       [R3]
                      S||S   |          |
[Line GND] O----------+||+---+----------+---O [Sleeve]

Explanation of Symbols:

• [R1]: 2.2 kΩ series resistor (primary side attenuation)
• T1: 1:1 audio transformer
• [C1]: 2.2 µF capacitor (DC blocking)
• [R2]: 100 Ω damping resistor (across secondary)
• [R3]: 2.2 kΩ MIC detect resistor (between MIC and GND)
• [Line IN], [Line GND]: input from radio/sound card
• [Ring 2], [Sleeve]: TRRS plug connections to smartphone